power mac g4
Power Mac G4 ROM Update 1.0 (10/18/1999)
During testing, Apple has discovered a potential problem that may cause data corruption or system crashes in certain situations on Power Mac G4 (PCI Graphics) systems more>>
During testing, Apple has discovered a potential problem that may cause data corruption or system crashes in certain situations on Power Mac G4 (PCI Graphics) systems. The Power Mac G4 ROM 1.8.1 Update includes fixes for data or file corruption that may occur after a Photoshop crash with Virtual Memory on and Extensis Photo Tools installed. For more about this software, check out the readme file.
Apple PowerBook Firmware 4.29
The PowerBook Firmware Update 4.2.9 will only run on 550MHz or 667MHz PowerBook G4 computers running Mac OS 9.1 or later from a local drive more>>
The PowerBook Firmware Update 4.2.9 will only run on 550MHz or 667MHz PowerBook G4 computers running Mac OS 9.1 or later from a local drive. If you are using Mac OS X you must boot from a local Mac OS 9.1 writeable partition (not a CD, or network disk) prior to following the update instructions. Firmware Update 4.2.9 includes improvements to Firewire target disk mode when running Mac OS X, and improves starting up on systems with 1gigabyte (GB) RAM and enables Netbooting over gigabit Ethernet.
It appears most RAM vendors will replace RAM if you find yours has been disabled by this firmware.
Apple Mac OS Update 9.2.2
This is the latest Mac OS update from Apple that improves Classic application compatibility in Mac OS X and delivers updated support for Macintosh systems that are based on the PowerPC G3 or G4 more>>
This is the latest Mac OS update from Apple that improves Classic application compatibility in Mac OS X and delivers updated support for Macintosh systems that are based on the PowerPC G3 or G4 processor.
with Mac OS 9. It provides additional FireWire and USB support, enhances networking and power ... with the Palm desktop and prevents HotSyncing between your Palm organizer and desktop Mac. ForThis release corrects a variety of problems that have emerged since the initial release of Mac ... should not install this update: Macintosh Performa 4400 or a Power Macintosh 4400, 5500, 6500Apple PowerBook G4 Firmware 4.29
The PowerBook Firmware Update 4.2.9 will only run on 550MHz or 667MHz PowerBook G4 computers running Mac OS 9.1 or later from a local drive more>>
The PowerBook Firmware Update 4.2.9 will only run on 550MHz or 667MHz PowerBook G4 computers running Mac OS 9.1 or later from a local drive. If you are using Mac OS X you must boot from a local Mac OS 9.1 writeable partition (not a CD, or network disk) prior to following the update instructions. Firmware Update 4.2.9 includes improvements to Firewire target disk mode when running Mac OS X, and improves starting up on systems with 1gigabyte (GB) RAM and enables Netbooting over gigabit Ethernet.
NEC-Mitsubishi Monitor Power patch 1.0.1
NEC-Mitsubishi has identified a compatibility issue between some models of display monitors and some Apple Macintosh G4 computers that causes the display monitor to remain off after a restart or more>>
NEC-Mitsubishi has identified a compatibility issue between some models of display monitors and some Apple Macintosh G4 computers that causes the display monitor to remain off after a restart or powering up after shutdown. On certain versions of the Mac OS ROM, this will only occur if the G4 has been in sleep mode. NEC-Mitsubishi has identified the cause as an incompatibility in the Mac G4s with OS 9.0.4 and Mac OS ROMs versions 4.9.1, 5.2.1 and 5.5.1, and Mac OS 9.1 Upgrade with Mac OS ROM 6.1. This causes "power off" commands to be sent to the monitor on shutdown and restart, however no matching "power on" command is sent instructing the monitor to wake up as the Mac powers up. The problem only appears on certain monitors because they support an optional industry standard alternate power command system that has been introduced on the new G4s. It is important to note that the monitor is functioning normally and is just following commands sent from the Mac. The following Mitsubishi monitors are affected by this issue:
- Diamond Pro 2045
- Diamond Plus 120
- Diamond Plus 200
- Diamond Plus 220
- Diamond Plus 730
- Diamond Pro 720
- Diamond Plus 710s
- Diamond Pro 920
- Diamond Plus 91
- Diamond Plus 92
ALi 7101 Power Management Controller 1997-04-21
This driver release supports the following devices: ALi 7101 Power Management more>> This driver release supports the following devices:
- ALi 7101 Power Management Controller
This driver release supports the following devices: ALi 7101 Power Management. ALi 7101 Power ...This driver release supports the following devices: ALiSiS Power Management Controller 1999-01-26
This driver release supports the following devices: SiS Power Management more>> This driver release supports the following devices:
- SiS Power Management Controller
following devices: SiS Power Management. SiS Power Management Controller 1998-01-09 - Tyan ...This driver release supports the following devices: SiSRtx PnP and Power Management Device 6.1.0.0
Rtx PnP and Power Management more>> Rtx PnP and Power Management Device<<less
Canon ScanGear CS 7.1.3.3
This ScanGear CS Scanner Driver is compatible with existing iMac, G3,G4 & Apples latest G5 systems equipped with built-in USB 1.1 or 2.0 ports more>>
This ScanGear CS Scanner Driver is compatible with existing iMac, G3,G4 & Apple's latest G5 systems equipped with built-in USB 1.1 or 2.0 ports. The ScanGear CS v7.1.3.3 Scanner Driver is for the CanoScan LiDE 50 scanner running on Mac OS 9.0 or higher and Mac OS X "Classic Mode". This self-mounting scanner driver installer assists the user with a guided installation procedure through an intuitive interface.
MP3 Player Power Control Driver 1.0.7.1
This driver release supports the following devices: MP3 Player Power Control more>> This driver release supports the following devices:
- MP3 Player Power Control Driver
SiS 5595 Power Management Controller 1995-12-31
This driver supports the following devices: SiS 5595 Power Management more>>
This driver supports the following devices:
- SiS 5595 Power Management Controller
Open Transport Update 2.6 (1/4/2000)
Open Transport 2.6 addresses DHCP issues in Mac OS 9, and prevents Macintosh computers from being used in certain types of Denial of Service (DoS) issues more>>
Open Transport 2.6 addresses DHCP issues in Mac OS 9, and prevents Macintosh computers from being used in certain types of Denial of Service (DoS) issues. Open Transport is the networking software in the Mac OS. This software installer updates Open Transport to version 2.6. This updater is for use only on computers using Mac OS 9.0, and Power Mac G4, iBook, and iMac (Slot-loading) computers running Mac OS 8.6.
HP Ethernet with LAN remote power adapter 4.38.0.0
HP Ethernet with LAN remote power more>> HP Ethernet with LAN remote power adapter<<less
win98 ct.zip 1999-11-24
This driver release supports the following devices: WinFast 5595 Power Management Controller WinFast more>> This driver release supports the following devices:
- WinFast 5595 Power Management Controller
- WinFast 6200MA
